2020 39 00

Ultra microcell holder for cells of 50ul working volume. Use special cell part number 2020 07 01, UV grade silica, 10mm pathlength.

4002 32 00

Dual water analysis sample holder designed to accommodate both 10mm pathlength rectangular cuvettes and 16mm diameter reaction tubes used with Merck SpectroQuant test kits. Time is saved as the need to replace cell holders is eliminated.

1010 31 00

Holder for single 10mm pathlength cell.

1010 39 00

Holder for cylindrical cells of pathlengths up to 100mm

2021 30 00

Ultra microcell holder for cells with working volumes of 10ul (10mm pathlength, part number 202 07 64) and 5ul (5mm pathlength, part number 202 07 63). Cells should be ordered to suit individual circumstances. The holder provides high precision alignment for maximum performance.

3021 37 00

Automatic cell changer for 8 cells for use in tablet dissolution systems. The changer is supplied with a replacement cell compartment lid and pipe guides. The changer is fully programmable when used in conjunction with software Program C (Cell programming) or controlled externally from PC.

2020 37 00

Holder for sipette/sip flowcells with pathlengths up to 50mm. A retaining screw ensures that cells are securely retained in the optimum position

1010 36 00

Holder for 4 cells with pathlengths up to 50mm. Must be used in conjunction with 4 position manual cell changer (Part number 1010 34 00).

2020 31 20

Thermoelectric (Peltier) controlled cell holder for a single10mm pathlength rectangular cell. Water circulation is provided for heat removal when working at temperatures below ambient. Used with CE2024 Thermoelectric Programmable Controller. Requires 1010 05 00 cell compartment lid and pipe guide.

2021 21 00

Return micro-sipette system comprising peristaltic pump and mounting assembly, swan neck sample probe, sample probe mounting block, all tubing and operating software. Sample volume size may be programmed and samples saved for further analysis or pumped to waste.

2020 36 15

Water thermostatted cell holder for 4 x 10mm pathlength cells shown fitted to automatic 4 cell changer (Part No. 2021 34 00) Automatic cell holder must be ordered separately. Requires 1010 05 00 Cell compartment lid and pipe guide.

2010 36 00

Cell holder for 4 cells of pathlengths from 20 to 40mm for use with 4 position automatic cell changer (Part No. 2021 34 00). Cell changer musr be orderd separately.

2021 34 00

Automatic changer for 4 cells. The photograph shows the cell changer with a holder for 4 x 10mm pathlength cells which is not included in the purchase price. The cell changer also accomodates 2020 36 15 water thermostatted cell holder which should be ordered to suit individual user requirements. When used in conjunction with Software Program C, the cell changer is fully programmable.

2021 24 00

Holder for 4 x 10mm pathlength rectangular cells for use with automatic cell changer (Part No. 2021 34 00) which must be ordered separately.

2021 34 00 with 2020 36 15

Automatic changer for 4 cells fitted with a water thermostatted with holder for 4 x 10mm pathlength cells. Both items should be ordered separately. When used with Software Program C the cell changer is fully programmable. Requires 1010 05 00 cell compartment lid and pipe guide.

2021 36 00

Automatic changer with integral holder for 6 x 10mm pathlength rectangular cells. When used with Software Program C the cell changer is fully programmable for speed and convenience.

2020 38 00

Manual microcell changer and holder for 4 cells. A beam focussing system and 2 part sliding base allow optimum adjustment for maximum light transmission for precise measurements.

1010 34 00 with 1010 24 00

Manual cell changer with holder for 4 x 10mm pathlength cells. Changer and holder to suit individual application should be ordered separately.

2020 35 00

Water analysis manual cell changer and combined holder for rectangular flowcells with pathlengths of 10, 20 and 40mm. Cells of different pathlengths may be permanently mounted in series in the holder. The cell most suited to the particular application being undertaken may be selected and used. The risk of breakage of expensive flowcells is significantly reduced. Spacers are included for maximum flexibility in choice of cell pathlength.

1010 36 15

Water thermostatted cell holder for 4 x 10mm pathlength cells. This holder should be used with manual 4 cell changer (Part No. 1010 34 00) available at extra cost. Requires 1010 05 00 Cell compartment lid and pipe guide.

1010 02 00

Holder for a single 4 inch x 0.5 inch test tube

1010 38 00

Holder for long pathlength rectangular cells up to 100mm pathlength. Extended thumbscrews enable rapid and convenient cell holder change.

1010 05 00

Cell compartment lid and pipe guide port for use with all single beam spectrophotometer water thermostatting systems.

4002 34 00

Water analysis combination cell holder accepting both 16mm reaction tubes and 1 inch square cells for convenience.

2010 32 00

Cell holder for single 10mm pathlength cell with sample stirring. Must be used in conjunction with cell stirring controller (Part No. 7200 31 01)

2010 33 00

Cell holder for 10mm pathlength single cell with cell stirring and water thermostatting. Must be used in conjunction with cell stirring controller (Part No. 7200 31 01) and cell compartment lid and pipe guide (Part No. 1010 05 00)

2010 34 00

Automatic cell changer for 4 x 10mm pathlength cells with cell stirring and water thermostatting. Must be used in conjunction with cell stirring controller (Part No. 7200 31 01) and cell compartment lid and pipe guide (Part No. 1010 05 00). When Software Program C is activated the cell changer is fully programmable.

7200 31 01

Electronic controller for sample stirring at speeds up to 1500 rpm. Must be used in conjunction with selected cell holder. Choose from 2010 32 00, 2010 33 00 and 2010 34 00. Supplied with a cell stirring bar.

CE3073

Integrating sphere with reference standard. A dedicated, compact high performance Spectralon coated integrating sphere is used for diffuse reflectance and diffuse transmission measurements. The sphere unit has its own silicon diode detector using a separate channel within the spectrophotometer. Use with CE3055 Reflectance Spectrophotometer

CE3075

Specular Reflectance Unit with flat sample rest, conical lens mounting rest, mounted front surface aluminised plain reference mirror and mounting thumb screws. This accessory is used for the specular reflectance measurement of surfaces and coated opthalmic lenses. It is ideally suited to quality assurance in the production of anti-reflection coatings and the measurement of thin film thickness.

CE3077

Opthalmic lens holder for transmission measurements with lens centring, mounting plate and mounting thumb screws.

2020 33 00

Solid sample or film holder. Accepts samples up to 10mm thickness.